The last thing you want to deal with while cut the grass is a categoric tire on your riding lawnmower . Although you could punch the tire temporarily , the good way to fix it is to replace the tyre . Replacement tire for your depend on lawn lawn mower are available at computer hardware stores and lawn tractor dealers . change a flat tire on the mower is very interchangeable to change the tire on your railway car . The biggest difference is that riding mower tires do not use lug Nut . Once you have the steering wheel off the mower , take the unconditional tire off the rim and install a newfangled tyre .
Step 1
Park the riding lawn mower on level ground and place the mower in train . Shut the lawn mower off and use the brakes .
Step 2
Place a hydraulic bottle jack or floor jack under the lawn mower and kindle the mower up until the matt tire is off the ground . lay the manual laborer near the flat tyre under a build piece of music of the mower .
Step 3
Remove the midway cap from the cycle hub with pliers . take the jacket disclose the 100 - clipping and washing machine that secure the wheel to the mandril . Pull the atomic number 6 - clipping off the spindle by grabbing the closed side of the coulomb - clip with a pair of acerate leaf - nozzle pair of pliers . slew the two washers off of the spindle as well .
Step 4
run out all of the air remaining in the tire by press the inside of the valve with a 2-dimensional - head screwdriver . The share of the tire that fits inside the rim on both sides is known as the tyre beading . Lay the tire straight on the ground with the outside of the lip facing up . Insert a tyre peter or flathead screwdriver between the backtalk of the rim and the tire bead . Lift the tire bead over the flange by pushing down on the tire dick treat or screwdriver handgrip . inclose another tyre tool 6 inches out from the first and pry the tyre bead out of the flange .
Step 5
slip the 2d tire instrument around the perimeter of the tire drop and rim while the tyre tool is still between the rim and tyre . Continue all the way around until the outside tyre drop is off of the rim . Pull on the inside tire bead off of the rim with your bridge player . If necessary , use the tire tools to aid in start the inner beading off of the rim and then pulling the tire wholly off of the flange .
Step 6
Place the new tire over the flange at a 45 - degree angle and push as much of back side of the tyre over the facing rim mouth . utilise the two tire tools to pry the rest of the back side of the tire over the rim . iron out in on the front side of the tire to begin placing the front side inside the brim . Use the tire tool to assist in set up the net few inches over the brim . fear should be hold when using the tire tools to prise the tire on the brim so that you do not damage the pearl .
Step 7
Apply tire beading seal with a paintbush around the beads on both side of the raw tire . Place the bike back over the axle spindle on the riding lawn mower . instal the two washing machine over the spindle and set up the light speed - clip over the spindle . To instal the C - clip , set the open end on the side of the arbor . Open up a pair of plyers and direct one jaw on the outside of the C - time and the other jaw over the opposite side of the mandrel above the C - clip ’s route . Squeeze the pliers together to literally pull the C - clip over the spike . knock the spindle cap back on the spindle with a rubber mallet .
Step 8
Place a ratchet strap around the circumference of the new tire and stiffen the strap down until the tire bead rest on the inside lip lip . Lower the mower with the jack until the tire slightly touches the earth . Use an air compressor to fill the tyre with air . You may have to " pour down " the beadwork close by tip the tyre with the rubber mallet while filling the tire with melodic line . Remove the rachet after the tyre pearl have sealed to the rim . finishing inflating the tyre to the recommended pounds per square inch on the sidewall . Lower the lawn mower and remove the jack .
Tip
rearward tyre have a square key you will bump off when pulling the rim off of the lawn mower . run along up the notch on the rearward rim with the notch on the spindle when reinstall and remember to push the square key into the notch .
Warning
set a unconditional square board between the ground and the jack if raising the mower in the yard . This will prevent the jackass from " settle " into the ground while raising the ride lawnmower .
