Build This DIY Planter Shelf To Grow Lots Of Plants In Little Space

Container gardening remains a red-hot trend . With Boomer gardeners downsizing and Millennials choosing pared - down flat over suburban Colonials , small - scale growing is where it ’s at . This DIY planter shelf puts you on thecontainer gardeningbandwagon by combining a vertical element with container to maximize your maturate place .

With just a few plain minute and a short list of supply , you’re able to grow herb , veggies or flowers on a balcony , terrace , deck of cards or porch . Each of the three tiers on this DIY plantation owner shelf holds four to six different flora . Though I grow wraith - loving perennials and annuals in mine , if you ’re look to fill this ledge plantation owner with homegrown green goods , adjudicate growing a combining of dwarf veggies like Fairy Taleeggplants , Tom Thumb tomatoes and Jingle Bell peppers in yours .

Materials & Tools

Step 1: Measure & Cut The Shelves

Begin by measure the distance of your plastic windowpane box planters . bring eight to 10 inches to that length and use a circular or table come across to burn the 1 - by-8 treat lumber display board into three piece , each equal to this length . In my example , each of the cut boards measure 36 in long . These boards will become the “ steps ” of your DIY planter ledge .

Step 2: Measure & Cut The Back Legs

On a level aerofoil , take one of the stair stringer and turn over it upside down so the small end is flat against the ground . Use a tape measure to measure the length between the top edge of the stair stringer and the ground , doing your best to make certain the tapeline measure meets the soil at a 90 level slant . Use a round or table take in to cut the 2 - by-4 into two pieces , each equal to this measurement . These will be the back legs of your DIY planter ledge .

Step 3: Attach The Legs To The Stair Stringers

Lay one of the stair stringers on the ground upside down , with the end that will be the top of the planter shelf pointing aside from you . lie the other stringer on the ground next to the first one so the stair notch of both stringers are facing out from each other . Lay one of the trimmed 2 - by-4 section on top of one of the stringers so the top edges are flush and the back of the stringer is loaded with the edge of the 2 - by-4 ( see photo).Jessica Walliser

Lay the other shorten 2 - by-4 section on top of the other stringer , again hold start the top edge and the back flush . habituate two wood screws to attach the leg to the stair stringer , locating the screws approximately 10 inches apart . Repeat with the other step stringer and 2 - by-4 . These will be the two support of your DIY planter shelf .

Step 4: Prepare To Attach The Shelf Boards To The Stair Stringers

uprise one of the step stringers with the support leg now confiscate and set it upright , so the base of the stringer and peg are resting on the solid ground ( and the leg is facing what will be the inside of your DIY planter shelf ) . require a partner to hold it upright , or shore it against a chairperson , table or other sustenance . Lift the other stringer and leg , and position it so it ’s asunder from the first stringer by the same breadth as the base of your window box plantation owner ( again , keep the leg facing what will be the inside of your shelf ) . Next , consist one of the 1 - by-8 shelf boards across the bottom stair mountain pass so the control board is stay on both of the step stringers at the same clip . valuate the overhang of the shelf plank on each side to see the board is center on between the two step stringers .

Step 5: Attach The Bottom Shelf Board To The Stair Stringers

Once the bottom shelf display panel of your DIY plantation owner box is centered between the bottom step notches , have sex it into place using two wood screws on either end , set about four inches apart . Make certain the screw locomote through the card and down into the stair stringer .

Step 6: Attach The Remaining Shelf Boards To The Stair Stringers

Once the bottom shelf is in place , repeat the cognitive operation with the middle and top control board shelves . Again , be sure to measure the overhang on either destruction of the shelf to ensure it ’s focus on and aligned with the other ledge boards . Jessica Walliser

Step 7: Add The Window Boxes

After all three steps are screwed into place , position a plastic window box on each shelf , keeping it center on .

Step 8: Fill & Plant The Boxes

Fill each of your widow boxwood plantation owner with a 50/50 mixture of in high spirits quality potting soil and compost . Your DIY planter shelf is now ready to be imbed .

article-post